|
Part |
PCB mark |
Type |
Power |
Value |
Source |
Manufacturer product # |
Notes |
other | |
|
Resistors |
R1 |
Through hole |
0.25 Watts |
100 kOhms |
CF14JT100K | ||||
|
R2 | |||||||||
|
R3 |
Through hole |
0.25 Watts |
220 kOhms |
CFR-25JB-52-220K | |||||
|
R4 |
Through hole |
0.25 Watts |
2.4 mOhms |
CF14JT2M40 | |||||
|
R5 |
Through hole |
0.25 Watts |
100 Ohms |
CFR-25JR-52-100R | |||||
|
R6 |
Surface mount |
0.25 Watts |
100 kOhms |
- |
Potentiometer |
with On/Off switch | |||
|
R7 |
Through hole |
1 Watt |
820 Ohms |
MFR-25FBF52-866R | |||||
|
R8 |
Through hole |
0.25 Watts |
12 kOhms |
CF14JT12K0 | |||||
|
R9 |
Through hole |
0.25 Watts |
750 kOhms |
CF14JT750K | |||||
|
R10 |
Through hole |
0.25 Watts |
150 Ohms |
CF14JT150R | |||||
|
R11 |
Through hole |
0.1 Watt |
100 kOhms |
06TR4AA104CP |
Potentiometer |
Frequency Adj. | |||
|
Boost Conv. |
Through hole |
0.1 Watt |
200 kOhms |
3296P-204 |
Potentiometer |
Voltage Adj. | |||
|
Capacitor |
C1 |
Through hole |
50 Volt |
0.22uF |
FG14X7R1H224KNT00 | ||||
|
Diodes |
D1 |
LED |
Blinking Red |
5mm |
XBMDK53D |
Flashing | |||
|
D2 |
LED |
Blue |
5mm |
WP7113LVBC/D |
Constant | ||||
|
D3 |
LED |
Yellow |
5mm |
WP7113SYCK/J3 |
Constant | ||||
|
D4 |
Through hole |
100 Volts |
200 mAmps |
1N4148 | |||||
|
D5 | |||||||||
|
Transistor |
Q1 |
NPN |
40 Volts |
800 mAmps |
2N3904 | ||||
|
ICs |
U1 |
Dual OP Amp |
32V |
40 mAmps |
Texas Inst. LM358N/NOPB | ||||
|
U2 |
Supervisor |
3.075V |
- |
MCP100-315DI/TO | |||||
|
Connector |
AJ1 |
3.5mm Audio |
- |
DIP3 |
PG316 | ||||
|
AJ2 |
- | ||||||||
|
BMS Connector |
- |
PH 2.0 2P |
2 Pin Male |
- |
Solder to the BMS |
Battery Connect. |
Optional | ||
|
Battery |
- |
Polymer Lithium |
2.5 Amps |
3.7 Volts |
Female PH2.0 Connector |
10x40x50mm | |||
|
Boost Converter |
- |
DC to DC |
2 Amps |
5V-28V |
MT3608 |
Input Voltage |
2VDC -24VDC | ||
|
Note: To increase Voltage from Boost Converter to 30VDC, you need to de-solder blue 100 kOhms potentiometer and solder 200 kOhms potentiometer. Or use fixed 107 kOhms 0.25W resistor | |||||||||
|
If you choose to use fixed 107k resistor, please look at the PIC for your references https://bbmpulser.org/wp-content/uploads/2025/12/BBSA-3.0-front-top-view.jpg | |||||||||
|
Link to 107k Ohms 0.25W resistor https://www.digikey.com/short/dvzmr3v3 | |||||||||
|
BMS |
TP4056 |
Type-C |
4.2V |
1.2 Amps |
Battery Charge |
Module |
Battery Protection | ||
|
Note: You must get 1.2A black version BMS. You will need to adjust battery charge current on it to ~400mA. To do that, you will need to de-solder small SMD resistor marked “122”. | |||||||||
|
This resistor sets battery charge current. I’s connected to the chip pin 2. You need to replace it with 3.6 kOhms resistor. Size for replacement SMD resistor is 0603. You can buy it here | |||||||||
|
PCB |
BBSA 3.0 |
Rev 2 |
10.2025 |
- |
https://jlcpcb.com/ https://bbmpulser.org/wp-content/uploads/2025/12/BBSA-3.0-rev2-Gerber-10.2025.zip | ||||
|
3D Printed Case |
BBSA 3.0 |
PLA Plastic |
STL files |
Ver3.6 | |||||
|
3D Printed LED Spacer |
3x per Case |
https://bbmpulser.org/wp-content/uploads/2025/12/LEDs-spacer-2.4mm-3pc.stl_.zip | |||||||
|
Screws |
For the Case |
- |
- |
- |
M2 x 4mm |
4x per Case | |||
|
USB-C cable |
1 Meter |
Re-charge |
White |
- |
- | ||||
|
TENS Pads |
10 pairs |
Micro-Pulsing |
White |
- |
7cm long x 1.5cm wide |
11 pairs / kit | |||
|
Alligator Clips |
1 pair |
28mm |
Red / Black |
- |
G98 |
1 pair / kit | |||
|
Silver Rods |
1 pair |
6” long |
14AWG |
- |
99.99% purity |
1 pair / kit | |||
|
Cary Case |
#2 |
Black or Gray |
Zipper |
Hard |
19cm x 14cm x 6cm | ||||
|
3D Printed Plate |
Dual Jar |
White |
PLA |
Plastic |
https://bbmpulser.org/wp-content/uploads/2025/12/BECK-BOX-V2.0.2-DUAL-JAR-DISK-RING.stl_.zip | ||||
|
Wristband |
Breathable |
Cotton |
Elastic |
Blue |
size: 40cm x 7.5cm | ||||
|
* Wristband |
Breathable |
- |
Elastic |
Gray, white |
80mm x 80mm | ||||
|
Wire |
Electrode |
Cable |
White |
3.5mm |
3.5mm x 2mm | ||||
|
Laser Pointer |
2 x AAA |
Batteries |
Red |
650nm |
1 milli Watt | ||||
|
Batteries |
2 x AAA |
Kaseba |
- |
- |
Extra heavy duty 1.5 Volt |
1 pair / kit | |||
|
Digital Clock |
- |
Battery powered |
White, Blue |
Alarm |
Count Down | ||||
|
Battery |
AG10 |
Cell |
Button |
- |
Alkaline | ||||
|
TDS Meter |
0-10,000PPM |
Blue |
- |
Digital | |||||
|
Battery |
LR44 |
Cell |
Button |
- |
Alkaline | ||||
|
If you have any questions or need to order anything from the list or found an error please contact me support@bbmpulser.org or call +1.216.309.8522 | |||||||||